Black and Decker 3 in 1 Can Opener
Cord Protector
Fix Number FIX10169655
Manufacturer Part Number 330005-01
This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.
Installation Instructions
John from Hancock, MI
Did not come with grinding disc guard
While unit was unplugged I screwed clamp of guard around grinder. Read more...
Power Cord
Fix Number FIX10169875
Manufacturer Part Number 330072-98
This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.
Installation Instructions
John from Hancock, MI
Did not come with grinding disc guard
While unit was unplugged I screwed clamp of guard around grinder. Read more...
Drain Valve
Fix Number FIX10049094
Manufacturer Part Number N286039
This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.
Installation Instructions
Steven from SMITHS STA, AL
Wouldn't hold air in tank.
Took old drain valve out and replaced with new one. Read more...
Bump Cap
Fix Number FIX10184171
Manufacturer Part Number 682378-02
2-5/8-Inch Wide This is a genuine Black and Decker replacement part. It is sold individually.. Its purpose is to hold the spool and bumper in the spool housing. It has 2 tabs that snap into the spool housing. To remove this part press on the 2 tabs and it will release from the spool housing.
Carbon Brush (Sold Individually)
Fix Number FIX10167153
Manufacturer Part Number 176846-04
This is a single OEM carbon brush. Two are needed to make a set, so if you require two, order accordingly. Carbon brushes are used to conduct electricity to the armature through its commutator. Brushes are a common wear part that will need to be replaced periodically due to consistent rubbing against the rotating commutator. Worn brushes can cause sparks around the commutator, which can also cause damage to the armature, which should also be inspected. If your electric motor is experiencing issues, the brushes should be one of the first things you check.
Ball Bearing (608D)
Fix Number FIX10169608
Manufacturer Part Number 330003-04
This ball bearing fits various gardening and lawn tools such as, electric drills, hammers, saws, and sander polishers. Ball bearings are used to reduce friction between rotating parts. This happens when the ball bearings take the load and spin to distribute the weight evenly without causing friction. The ball bearing function can reduce wearing and allows your tool to run smoothly. Replacing this part regularly is important for the function of your tool. Refer to the manual provided by the manufacturer for further installation instructions and guidance.
Brush and Spring
Fix Number FIX10166057
Manufacturer Part Number 145323-06
This carbon brush and spring kit includes a carbon brush, wire lead, and a spring. The parts fit a variety of tools such as saws. If you notice your motor is running poorly or is intermittent, then check the brush for damage, cracks, and burns. It is common to replace the brushes repeatedly as they easily wear off from friction and use. Tip: remember to inspect your armature for burns and cracks when replacing your carbon brushes. This will help identify larger motor problems. This part measures to 3/4 inches in length, 1/2 inches in width, and the 1/4 inches in thickness. Refer to the manual for installation instructions and a list of the parts included.
Regulator Repair Kit
Fix Number FIX10116454
Manufacturer Part Number N008792
This is an OEM regulator repair kit for air compressors. This kit contains all the parts and instructions needed to restore a broken regulator. It is normal for the inner parts of the regulator to wear and have to be repaired over time. Before beginning this repair make sure you release the pressure from the air tank.
Brush, Shunted
Fix Number FIX9927365
Manufacturer Part Number 242273-00
Installation Instructions
Herb from W BLOOMFIELD, MI
Worn brushes
Remove cover 4 screws. Remove brush cover 1 screw. Replace brush and reverse taking apart to assemble! Read more...
Black and Decker 3 in 1 Can Opener
Source: https://www.fix.com/parts/black-and-decker/